Heating & Cooling Controls

PG9 CARTRIDGE R BUSHING 32"LD

PG9 CARTRIDGE F CLIP 32" LEAD

Transformer, 40VA, 120/208/240 VAC Primary, 24 VAC Secondary, Plate, Foot Or Hub Mount, Universal Application

Transformer, 40VA, 120 VAC To 24 VAC, 60Hz, Plate Mounted, Primary10" Leads, Secondary Screw Terminals

Hub mount, 120VAC to 25VAC, 60Hz, 40VA, 10" leads (line), screw / spade terminals (load), with plate.

Transformer, 40VA, 120 VAC To 24 VAC, 60Hz

Hub mount, 120VAC to 25VAC, 60Hz, 20VA, 10" leads (line), screw / spade terminals (load).

PG9 Pilot Generators, 750 Millivolt. Provides a pilot flame for igniting gas burners while generating millivolt output to operate gas valves and relays

PG9 Pilot Generators, 750 Millivolt. Provides a pilot flame for igniting gas burners while generating millivolt output to operate gas valves and relays

PG9 Series 750 mV Generators and Pilot Burners. General Controls PG9 Style Combination Pilot Burner &Generator. 180°, 0.87” Length. Universal Replacement Includes Extra Base Fitting for LP Gas Application

PG9 Series 750 mV Generators and Pilot Burners. General Controls PG9 Style Combination Pilot Burner &Generator. 180°, 0.32” Porting Length

PG9 Series 750 mV Generators and Pilot Burners. General Controls PG9 Style Combination Pilot Burner &Generator. 90° Right and 90° Left, 2-3/16” Head Width

PG9A27TL014S2 Pilot Generator channel

PG9 Pilot Generators, 750 Millivolt. Provides a pilot flame for igniting gas burners while generating millivolt output to operate gas valves and relays

36" Junction Block Thermocouple With Energy Cut-Off

72" Thermocouple, 30 mV

48" Thermocouple, 30 mV

36" Thermocouple, 30 mV

30" Thermocouple, 30 mV

24" Thermocouple, 30 mV

18" Thermocouple, 30 mV

750 mV Power Generator, 36" Fiberglass Leads With F Spade Clips & PG9 Adapter

750 mV Power Generator, 36" Armored Cable With Spade Type Connections, Mounting Nut And Spring Clips

750 mV Power Generator, 36" Fiberglass Lead With Spade Type Connections. Direct Replacement For PG9 Models Without The Use Of PG9 Adapter Sleeve

750 mV Power Generator, 36" Armored Cable With Spade Type Connections, Mounting Nut, Spring Clips And PG9 Adapter Sleeve

S2, 750mV, 36" leads, armored cable, PG9 adapter, split-spade terminals, for use with E31-12 pilot burner.

Regulated LP To Natural Gas Conversion Kit For Use On Two Stage 36G, H, J, Valves. Regulation Range 1.0" To 4.0" W.C. Low Fire, 2.0” To 5.0 " W.C. High Fire

Natural To Regulated LP Gas Conversion Kit For Use On Two Stage 36G, H, J, Valves. Regulation Range 4.0" To 10.0" W.C. Low Fire, 6.0" To 12.0" W.C. High Fire

Adapter Kit For The 36G Gas Valves. Kit Includes: Connector (5/16" To 1/4" Hose Barb),Tube (5/16" O.D.) And Hex Wrench (3/32")

Natural To Unregulated LP Gas Conversion Kit For All 36C00 Valves. Use With External Regulator Set For LP Gas

Natural To Regulated LP Gas Conversion Kit For Use On Single Stage 36C, D, E, F, G, H, J Valves. Regulation Range 7.0 " To 12.0” W.C.

LP To Natural Gas Conversion Kit For Use On Single Stage 36C, D, E, F, G, H, J Valves. Regulation Range 2.5" To 5.0” W.C.

Water Seal Kit For 1311-104, 1311-133, 1315-104, 1361-104, 1361-133

Water Seal Kit For 1311-103, 1311-132, 1315-103, 1361-103, 1361-132

Water Seal Kit For 1311-102 And 1361-102

120V Coil Replacement For 25M Valve Individual Pack Booster & Holding Coil

120V Coil Replacement For 25M Valve Individual Pack Secondary Coil

Immersion Well Used With All Hydronic Controls With Bulb Size 3-1/2 X 3/8”. 3/4” NPT, Extra Extended Shank

Immersion Well Used With All Hydronic Controls With Bulb Size 3-1/2 X 3/8”. 3/4” NPT, Standard Extended Shank

Immersion Well Used With All Hydronic Controls With Bulb Size 3-1/2 X 3/8”. 3/4” NPT, Standard Shank

Immersion Well Used With All Hydronic Controls With Bulb Size 3-1/2 X 3/8”. 1/2 NPT, Standard Shank

Immersion Well Used With All Hydronic Controls With Bulb Size, Control Bulb Size 2-15/16 X 7/16”, 1/2” NPT, Standard Shank

Well, 3/4" NPT For 11B30-4

Immersion Well Used With 11B18, 11B05, 11B55, 1131 Hydronic Controls. 3/4” NPT, Standard Shank

Immersion Well Used With 11B18, 11B05, 11B55, 1131 Hydronic Controls. 1/2” NPT, Standard Shank

Immersion Well Used With 11B06, 11B37, 1182 Hydronic Controls. Control Bulb Size 3-1/2 X 7/16”, 1/2” NPT, Standard Shank

Immersion Well Used With 11B06, 11B37, 1182 Hydronic Controls. Control Bulb Size 3-1/2 X 7/16”, 3/4” NPT, Standard Shank

Immersion Well Used With 1609, 1629, 2A23 Hydronic Controls. Control Bulb Size 5-3/4 X 3/8”. 1/2” NPT, Standard Shank

Valve Assembly For 13A01

Valve Assembly For 1-1/4" 1311's And 1361's

Valve Assembly For 1" 1311's And 1361's

Valve Assembly For 3/4" 1311's And 1361's

Well Adapter For 11C00, 8B00, 8C00, 8D00, 8E00, 8F00 Series, Has Different Diameters To Fit Wells On Existing Installations

Brass Compression Fitting For 1/4" Pilot Line Connections 7/16"-24 Thread

F67-8535 Integrated Thermostat Sensor for independent thermostat functionality on the 50D50U-843 All-Spark™ Universal Intermittent Pilot/Direct Spark 24V Ignition Module.

Resistor Assembly, For Use With 36 Cycle Pilot Gas Valves With Pressure Switch (Natural Gas Applications Only) Plug-In Types Only, 3098 Type Mercury Flame Sensors

Body Seal Ring For 13A00 Zone Valves

Bracket For 3F05, 3L05 Snap Disc, (2) Terminal Adaptors

Packing Nut With 1/2" Thread, For Use With Remote Bulb Controls

NEW - Trane Style Adaptor Board For Installing 50N02A-820 Or 50N02B-820 On Commercial Rooftop and Package Units

Replacement Knob For 764 Series Valve

24 VAC Motor Only For 13A00 Zone Valves

24 VAC Power Head For 2 Way 13A00 Zone Valve With Plug-In Panel

24 VAC Power Head For 2 Way 13A00 Zone Valve With Conduit Hub

Motor Assembly For Zone Valves, (2 Wire Type)

Motor Assembly For Zone Valves, (3 Wire Type)

HOT WATER TANK CONTROL REPAIR KIT Rheem power vent control repair kit complete with 3050-1 flame sensor and F91-4162 replacement coil assembly.

Heat Transfer Compound Packing Grease With Well Adaptor For Use In Immersion Wells To Improve Thermal Conductivity/Thermal Response

Heat Transfer Compound Packing Grease For Use In Immersion Wells To Improve Thermal Conductivity/Thermal Response

7.5' Replacement Remote Sensor For 16E09-101

Wiring Harness Connector For HSI Systems

Wiring harness

NEW -1.5 Pole Contactor, 120 VAC Coil, 50/60 Hz, 40 Amp Contacts. Coil Data: 420 Ohms DC Resistance, 42 mA, 5 VA (Nominal), Maximum 20 VA (Inrush). Approximate Dimensions: 3-1/4" x 2" x 2 1/2"

1.5 Pole Contactor, 24 VAC Coil, 50/60 Hz, 40 Amp Contacts. Coil Data: 16.5 Ohms DC Resistance, 208 mA, 5 VA (Nominal), Maximum 20 VA (Inrush). Approximate Dimensions: 3-1/4" x 2" x 2 1/2"

1 Pole Contactor, 208/240 VAC Coil, 50/60 Hz, 30 Amp Contacts. Coil Data: 1,825 Ohms DC Resistance, 21 mA, 5 VA (Nominal), Maximum 20 VA (Inrush). Approximate Dimensions: 3 1/4" x 2" x 2 1/2"

1.5 Pole Contactor, 120 VAC Coil, 50/60 Hz, 30 Amp Contacts. Coil Data: 420 Ohms DC Resistance, 42 mA, 5 VA (Nominal), Maximum 20 VA (Inrush). Approximate Dimensions: 3-1/4" x 2" x 2 1/2"

1.5 Pole Contactor, 24 VAC Coil, 50/60 Hz, 30 Amp Contacts. Coil Data: 16.5 Ohms DC Resistance, 208 mA, 5 VA (Nominal), Maximum 20 VA (Inrush). Approximate Dimensions: 3-1/4" x 2" x 2 1/2"

Transformer, 75VA, 50/60 Hz 120/208/240V Pri, 24V Sec, Foot Mount, With Circuit Breaker

Transformer, 60VA, 50/60 Hz 120/208/240V Pri., 24V Sec, Foot Mount, With Circuit Breaker

Transformer, 50VA, 60 Hz, 120V/208/240 Pri., 24V Sec., Multi-Mount

Transformer, 50VA, 60 Hz, 120/208/240V Pri., 24V Sec., Foot Mount

Transformer, 50VA, 50/60 Hz 120/208/240V Pri., 24V Sec., Foot Mount, With Circuit Breaker

Transformer, 40VA, 60 Hz, 120/208/240V Pri., 24V Sec., Multi-Mount

Transformer, 40VA, 50/60 Hz, 120V Pri., 24V Sec., Multi-Mount

Transformer, 40VA, 60 Hz, 120/208/240V Pri.., 24V Sec., Foot Mount

Transformer, 40VA, 50/60 Hz, 208/240V Pri., 24V Sec., Foot Mount

Transformer, 40VA, 50/60 Hz, 120V Pri., 24V Sec., Foot Mount

TRANSFORMER

Heavy Duty Enclosed Fan Relay, 277 VAC Coil, 50/60 Hz, SPNO/SPNC. Coil Data: 10300 Ohms DC Resistance, 10.8 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48...

Heavy Duty Enclosed Fan Relay, 277 VAC Coil, 50/60 Hz, SPDT. Coil Data: 10300 Ohms DC Resistance, 10.8 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps...

Fan Relay, Type 184, 208/240 VAC Coil, 50/60 Hz, SPNO/SPNC. Coil Data: 6050 Ohms DC Resistance, 12.5 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps...

Fan Relay, Type 184, 120 VAC Coil, 50/60 Hz, SPNO/SPNC. Coil Data: 2000 Ohms DC Resistance, 25 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps. Inrush @...

Fan Relay, Type 184, 24 VAC Coil, 50/60 Hz, SPNO/SPNC. Coil Data: 77 Ohms DC Resistance, mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps. Inrush @ 250 VAC...

Fan Relay, Type 184, 208/240 VAC Coil, 50/60 Hz, SPDT. Coil Data: 6050 Ohms DC Resistance, 12.5 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush).

Fan Relay, Type 184, 120 VAC Coil, 50/60 Hz, SPDT. Coil Data: 2000 Ohms DC Resistance, 25 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush).

Fan Relay, Type 184, 24 VAC Coil, 50/60 Hz, SPDT. Coil Data: 77 Ohms DC Resistance, 125 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps. Inrush @ 250 VAC...

Fan Relay, Type 184, 120 VAC Coil, 50/60 Hz, SPNO. Coil Data: 2000 Ohms DC Resistance, 25 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps. Inrush @ 250...

Fan Relay, Type 184, 24 VAC Coil, 50/60 Hz, SPNO. Coil Data: 77 Ohms DC Resistance, 125 mA (Nominal), 3 VA (Nominal), 4 VA (Inrush). Contact Ratings: Inductive: 12 Amps. Continuous 60 Amps. Inrush @ 125 VAC; 8 Amps. Continuous, 48 Amps. Inrush @ 250 VAC...

2 Pole, Type 91, 208/240 VAC Coil, DPDT, 2 Sets Of Power Rated Contacts. 1,600 Ohms DC Resistance, 38 mA, 9.5 VA (Nominal), 22 VA (Inrush). Contact Ratings: 12FLA / 60LRA @ 125 VAC, 6FLA 35LRA @ 250 / 277 VAC, 15A @ 277 VAC RES, 1/2HP @ 125 / 250 VAC

2 Pole, Type 91, 115/120 VAC Coil, DPDT, 2 Sets Of Power Rated Contacts. 420 Ohms DC Resistance, 66 mA, 9.5 VA (Nominal), 22 VA (Inrush). Contact Ratings: 12FLA / 60LRA @ 125 VAC, 6FLA 35LRA @ 250 / 277 VAC, 15A @ 277 VAC RES, 1/2HP @ 125 / 250 VAC